1. Basic Troubleshooting

Start with some fundamental steps.

1. Restart: Shut down the system and disconnect the power cable. After waiting a minute, reconnect the power cord and turn on the system.
2. Compatible RAM: Verify that the newer RAM sticks you are attempting to use with XMP are compatible with your motherboard. Refer to the Qualified Vendor List (QVL) provided by the motherboard’s manufacturer for confirmation.

2. Check the Current RAM Speeds

Inspect your existing RAM speeds before adjusting any settings.

Open Command Prompt and run:

wmic memorychip get speed

3. Clear the System’s CMOS

The system’s CMOS retains its BIOS configurations, including memory controller settings that can prevent XMP from initializing if they are inaccurate. Resetting the CMOS can resolve the issue.

1. Power off the system and disconnect the power cable.
2. Open the case and locate the CMOS battery, which is similar to a watch battery but larger.
3. Gently remove the battery and hold down the power button for 30 seconds.

   

4. Wait a minute before reinserting the CMOS battery.
5. Replace the cover, reconnect the power, and turn on the system.
6. Boot into the BIOS, enable XMP, and save the settings.
7. Restart the system and observe whether the changes take effect.
8. If the issue persists, replace the CMOS battery with a new one and repeat the above steps.

4. Uninstall Conflicting Apps

Some applications may interfere with XMP at the operating system level, preventing the profile from functioning. Overclocking utilities such as the Dell Alienware Command Center may be the cause, and uninstalling any problematic software could resolve the issue.

1. Start Windows and right-click on the Start button.
2. Select Apps & Features and find the Dell Command Center.
3. Click to expand the options and select Uninstall.

   

4. Proceed with the uninstallation following the on-screen prompts.
5. After completion, restart the system and clear the CMOS (refer to previous steps).
6. Again, enable XMP in the BIOS and check if it is now functional.

5. Uninstall Intel Iris Xe Graphics Driver

Resource conflicts between XMP and the graphics driver may result in the operating system downgrading RAM speeds to maintain display functionality. This could be the issue when using the Intel Iris Xe Graphics Driver. Uninstalling it could resolve the problem.

1. Right-click the Start button and access Device Manager.
2. Expand the Display Adapters tab, right-click on the graphics device, and select Uninstall Device. In the confirmation box, select “Delete the driver software for this device.”

   

3. Follow through the uninstallation process, then restart the system.
4. Enter the BIOS setup, enable XMP, and record any improvements upon restarting.

6. Disable Memory Integrity on Windows

Memory Integrity is a feature of Windows’ core isolation that might prevent XMP modules from accessing necessary resources. Disabling this feature could solve the problem.

1. Open the Start menu and type Windows Security.
2. Launch it, navigate to Device Security, and click on Core Isolation Details.
3. Turn off Memory Integrity and reboot the system.

   

7. Connect the Extra Power Connector on the Motherboard

Motherboards come with multiple power connectors to cater to different power requirements. Some motherboards may need additional power to support XMP, and failing to connect this extra power connector can be a common oversight, especially by gamers. Securing this connection could resolve the issue.

1. Turn off the system and disconnect the power cable.
2. Open the case and locate any unused power connector, like an 8-pin or 4-pin connector that hasn’t been connected.

   

3. Attach the extra power connector appropriately and replace the case cover. If uncertain, refer to the motherboard’s manual or consult an expert for assistance.
4. Power on the system and test the efficacy of XMP.

8. Clean and Reseat The RAMs in the XMP Supported Slots

The XMP profile works in specific motherboard slots. If the RAM sticks are incorrectly seated or dust is present in the RAM slots, XMP may not engage. Cleaning and reseating the RAM in the correct slots could resolve this.

1. Power down the system and unplug the power cable.
2. Open the case and extract the RAM sticks from their slots.
3. Clean the slots and RAM using a Compressed Air Can.

   

4. Reinsert the RAM sticks into the correct slots, typically the A2 and B2 slots, which are the second and fourth channels from the CPU and are XMP-compatible.
5. If this method doesn’t yield results, proceed to remove the RAM sticks, cooler, and CPU. Ensure proper seating of all components and attempt to engage XMP once more.

9. Try XMP on One Stick at a Time

Faulty memory sticks or incompatibility with other hardware components can cause XMP to fail. Isolate the issue by testing XMP with each stick individually.

1. Shut down the system and disconnect it from the power source.
2. Open the system and remove all RAM sticks.
3. Reinsert just one stick into an XMP-supporting slot.

   

4. Close the case, reconnect the power, and reboot into BIOS.
5. Enable XMP, save settings, and observe its behavior within the OS.
6. Repeat this process with the other RAM sticks, ensuring they are placed in an XMP-compatible slot.

If XMP fails with any of the sticks, it may indicate that the stick is faulty or incompatible. Conduct further testing in a different system if necessary.

10. Edit the BIOS Settings

Certain BIOS settings could interfere with XMP’s functionality. Adjusting these settings may rectify the issue, keeping in mind that labelings and availability may vary depending on the system’s BIOS.

10.1. Update the BIOS to the Latest Version

Follow the specific guidelines of your system’s manufacturer for BIOS updates:

• Dell
• HP
• Gateway
• Lenovo
• MSI

Post-update, reassess XMP functionality. If your system features Management Engine Firmware, ensure it is also up to date.

10.2. Enable Resize Bar and 4G Decoding

1. Access the Advanced System Settings in the BIOS, set the Re-size Bar to Enabled, and enable 4G Decoding.

   

2. Save changes and reboot the system.
3. Upon restart, access BIOS once more and enable XMP.

10.3. Disable RGB Fusion

1. Navigate to Peripherals > RGB Fusion within the BIOS.

   

2. Disable RGB Fusion, save, and then restart.
3. Attempt to activate XMP again after reboot.

10.4. Disable Fast Memory Boot

1. In the BIOS, under Overclocking, locate and disable Fast Memory Boot.

   

2. After saving the changes, reboot and enable XMP to observe any changes.

10.5. Disable Auto Low Latency and High Bandwidth

1. Enter the BIOS and proceed to Advanced CPU Settings.
2. Turn off Auto Low Latency and High Bandwidth.

   

3. Save and restart the system.
4. Test XMP effectiveness within the operating system after reboot.

10.6. Reset BIOS to the Defaults

1. Inside BIOS, press F5 to load defaults, though the specific key might differ by system.
2. Confirm the reset action and save the settings once completed.

   

3. Reconfigure XMP settings in the BIOS after restarting.

10.7. Downgrade the System’s BIOS

The procedure for downgrading the BIOS closely resembles the update process. Locate and download an older BIOS version from the OEM’s website and apply the aforementioned instructions to downgrade.

11. Try Different Overclocking Modifications

XMP is essentially a form of RAM overclocking. If other components of the system aren’t aligned with XMP’s requirements, it might not function properly. Trying different overclocking configurations might be beneficial.

Since overclocking varies across different systems, we’ll outline some general steps below. However, precise instructions will depend on your specific hardware configuration.

11.1. Increase Voltage

• VCCSA: 1.35V or 1.25V.
• VDDQ TX (CPU): 1.4V.
• DRAM Voltage: 1.4V, 1.36V, 1.35V, 1.25V, or 1.2V.
• IMC Voltage: Within 0.5V of DRAM voltage.
• SoC Voltage: 1.25V or 1.30V.
• QPI/VTT: 1.25V.
• Adjust VDDCR SoC Voltage to offset mode and increase it by 6.5mV.
• VDD/VDDQ: 1.25V, 1.30V, or 1.4V.
• VDD2: 1.4V.

11.2. Timing Values

• Cycle Time (Trc): 57 or 65.
• Timings: 16-18-18-36, 40-40-40, or 36-36-36.

11.3. Frequency

• Frequency: 3000 MHz, 3200 MHz, or the maximum supported by your system.
• Set RAM speeds to the highest levels that both the system’s motherboard and CPU can accommodate. Refer to the system’s manual or the OEM’s website for the correct ratings.

Should the XMP issues persist, reach out to your system’s OEM support. The problem might be with the RAM sticks themselves or potentially with the motherboard, particularly if one of the RAM slots is defective.

The post How to Resolve XMP Not Working Issue? appeared first on Appuals.

Other factors contributing to this problem include physical damage to the docking station or its ports, improper connections, or compatibility issues with the laptop in use.

To troubleshoot, first inspect the docking station and cables for any physical damage. If no damage is visible, perform a reset by disconnecting all cables, including the power supply, and reconnecting them after a few minutes to reset the internal hardware.

If the issue persists, please try the following solutions.

1. Disable Power Management on Drivers

Begin by disabling the power management feature on the drivers in question. This action prevents Windows from disabling the adapter on your computer for power savings.

Disabled adapters often lead to non-functioning peripherals connected to the Dell docking station. You must locate the affected hub and disable power management for that specific driver using the Device Manager.

1. Open the Start Menu and search for Device Manager, then open it.

   

2. Next, expand the category relevant to your docking station’s issue.
3. If USB hubs are problematic, for instance, expand the Universal Serial Bus Controllers list.
4. Right-click on the target driver and select Properties.
5. Go to the Power Management tab.
6. Uncheck the Allow the computer to turn off this device to save power option.

   

7. Click OK.

2. Install Relevant Drivers

Another cause for a non-functioning Dell docking station is missing drivers on your computer. Without the necessary drivers, peripherals cannot communicate with your PC.

To fix this, install the required drivers. For instance, if the docking station’s LAN port is non-operational, make sure you have installed the appropriate RealTek ethernet controller drivers.

1. Navigate to the official Dell drivers support website by following this link.
2. Search for your specific Dell dock.
3. Download and install the relevant drivers for your device.

   

4. Restart your computer and check if the problem has been resolved.

3. Disable Display Stream Compression

If you encounter issues with external monitors connected through the Dell docking station, consider disabling Display Stream Compression (DSC) through the Windows Registry.

DSC manages the video signal’s available bandwidth. Deactivating this feature can enable the monitors to receive input signals correctly.

1. Open Notepad by searching for it via the Start Menu.

   

2. Copy and paste the following code snippet into Notepad:

   Windows Registry Editor Version 5.00 
   
   [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class{4d36e968-e325-11ce-bfc1-08002be10318}\0000]
   "DPMstDscDisable"=dword:00000002
   
   [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class{4d36e968-e325-11ce-bfc1-08002be10318}\0001]
   "DPMstDscDisable"=dword:00000002
   
   [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class{4d36e968-e325-11ce-bfc1-08002be10318}\0002]
   "DPMstDscDisable"=dword:00000002

3. Choose File > Save As.

   

4. Name the file Disable_DSC.reg and set All Files as the file type.

   

5. Run the registry script you have created.
6. Restart your computer to apply the changes.

4. Power Reset Dell Docking Station

Power resetting the Dell docking station can fix inconsistencies within the device. This action resets internal settings and helps the docking station to start anew.

Power off the Dell docking station, disconnect all cables, and remove the power adapter. Wait for about 10 seconds before reconnecting the power adapter and turning the station back on.

Once powered on, reconnect your peripherals to see if the issue has been resolved.

5. Update Dell Docking Station Firmware

Outdated firmware might also prevent a Dell docking station from functioning correctly. Updating the firmware with the provided utility can resolve such issues.

Dell offers a firmware updating tool specific to its docking stations, facilitating the installation of the latest updates.

1. Access the Dell Driver support website by clicking this link.
2. Find your docking station model on the website.
3. From the downloads section, acquire the firmware update utility.

   

4. Connect the docking station to your PC.
5. Execute the firmware update utility as an administrator.
6. Let the tool perform diagnostics on your docking station.
7. Begin the update process by clicking Update.

   

8. Upon completion, reboot your computer.

With these solutions, you should be able to get your Dell docking station working properly. If the station still does not function, reach out to the Dell support team for further assistance.

The post How to Troubleshoot a Non-Working Dell Docking Station? appeared first on Appuals.

The problem mainly stems from a software glitch, which requires a patch from the development team. In this article, we will guide you through several steps to eliminate the delay from your Xbox Elite controllers.

1. Switch Monitor Preset

Start by adjusting your monitor’s profile. Most monitors feature various modes tailored for different activities. For gaming, it’s advisable to switch your monitor to ‘Game Mode’.

Doing so can help reduce on-screen delay when using a controller. Access the on-screen menu using the monitor’s back buttons and enable the ‘Game’ preset.

The menu’s exact location will vary by manufacturer, but typically, it’s fairly straightforward to navigate once you enter the menu settings.

2. Change Controller’s Profile

For Xbox Elite controllers used on Windows, settings profiles are managed through the Xbox Accessories app. Certain profiles can inadvertently introduce response delays.

1. Connect your Elite Controller to your PC.
2. Launch the Xbox Accessories app, searchable from the Start Menu.

   

3. Select your controller and press Configure within the app.
4. Choose the currently enabled profile and select Edit.

   

5. Ensure that the Sensitivity curve option is not set to Delayed.

   

6. Select from Default, Instant, Aggressive, or Smooth.
7. Adjust the Right stick settings accordingly.
8. Test your changes within a game to verify if the delay still exists.

Employing the default keymaps on your PC can often lead to an input lag. Usually, this occurs due to software inconsistencies, thus it’s recommended to revert to the default keymaps until the issue is addressed.

1. Access the Mapping section in the right pane.
2. Select Restore to Default to reset the keymaps.

   

3. Once reset, check for ongoing input lag issues.

3. Update Controller Firmware

Outdated firmware can also lead to controller lag. To address this, update your controller’s firmware. Update your Xbox controller either through the console or a PC.

3.1. Using Xbox Console

1. Press the Xbox button on the controller.
2. Go to Profile & system > Settings.
3. Select the Devices & connections tab within Settings.

   

4. Choose Controllers & headsets or Accessories, depending on your console model.
5. On the Xbox controller screen, select the three dots.
6. Choose Firmware Version.
7. Click Update Now and follow the prompts.
8. Allow the update process to finish.

3.2. Using Windows

1. Open the Xbox Accessories app on your PC. Download it from the Microsoft Store if needed and connect your Xbox Elite Controller.

   

2. Connect the controller to the system via USB or the Xbox Wireless Adapter.
3. Select the three dots on the controller screen.
4. Click Update Now and follow the instructions for any available firmware updates.

   

5. After the update, assess if the delay issue still persists.

4. Enable Game Mode

Activating Game Mode in Windows can yield better performance during gameplay and may reduce a connected controller’s input latency.

1. Press Win key + I to open the Settings app.
2. Navigate to Gaming > Game Mode.

   

3. Turn on Game Mode using the available slider.

5. Power Cycle Xbox Elite Controller

If the previous solutions were ineffective, consider power cycling the Xbox Elite controller to reset it and clear any glitches.

To power cycle your controller:

1. Press and hold the Xbox button for 5 to 10 seconds until the controller shuts off.
2. After it has completely turned off, wait a few seconds and then press the Xbox button again to turn it back on.
3. Check if this rectifies the lag issues.

Should the lag with your Xbox Elite controller persist, consider contacting the support team for further assistance or a potential replacement.

The post How to Fix Xbox Elite Controller Lagging Issue? appeared first on Appuals.

Fortunately, there are several methods available to reset your BIOS password. Doing so will grant you access to the BIOS menu, where you can then change or set a new password if you wish. Below is a guide outlining the three most effective methods for removing a BIOS password, allowing you to choose the most feasible option for your situation.

1. Remove CMOS Battery

The simplest method to remove the BIOS password is by taking out the CMOS battery on your motherboard. The CMOS battery maintains your BIOS settings; hence, removing it resets the motherboard to its default settings.

This process involves opening your PC to physically remove the battery. If you’re not comfortable handling the hardware, consider trying the next method.

1. Begin by powering off your computer and unplugging the power cable.

   

2. Next, remove the cover from your PC to access the motherboard.
3. Locate and remove the CMOS battery from the motherboard. Refer to the image below if you are unsure of its appearance.

   

4. Leave the CMOS battery out for at least 5 minutes to discharge, which will erase your BIOS settings.
5. Reinsert the CMOS battery into its slot and reconnect your power cable.
6. Power on your computer and access the BIOS menu.
7. You should now find that the BIOS password has been reset, permitting entry to the BIOS menu.

2. Use a Master Password

Resetting the BIOS password can also be achieved by using a master password. Motherboard manufacturers typically provide a master password that corresponds to a system code, which can be used to bypass the BIOS menu in such situations.

Master passwords are unique and based on the system code displayed after entering the incorrect BIOS password several times. Follow these steps to use a master password:

1. Firstly, restart your computer and proceed to the BIOS password entry screen.
2. Input an incorrect password three times.

   

3. A code should then be displayed on the screen.

   

4. Make sure to note down this code or take a photo to ensure you have a record of it. If a code is not shown, you may need to obtain a master password from the manufacturer using the laptop’s serial number or another method. For hints, you may refer to the table on the website linked below.
5. Access the BIOS Password website by clicking here.
6. Input the code you received and select Get Password.

   

7. The site should provide you with one or more passwords.
8. Restart your computer and try these passwords; one of them should enable access.

3. Use CLR CMOS Jumpers

You can also clear the BIOS settings by using CLR CMOS jumpers on your motherboard. This is an alternative to removing the CMOS battery, and every motherboard includes these jumpers.

Instead of extracting the battery, you can short the CLR CMOS pins on the motherboard. The number of pins—two or three—varies depending on the motherboard model.

1. Power off your computer and detach the power cable, as before.

   

2. Open your PC to gain access to the motherboard.
3. Identify the CLR CMOS jumpers on the motherboard, marked with the text “CLR CMOS” nearby or underneath the pins.

   

4. If there are three pins, connect the second and third pins to clear the BIOS; for two pins, short them together using something conductive, like a screwdriver tip.
5. Hold the short for a minimum of 30 seconds.
6. Reconnect the power cable and power up your PC.
7. The BIOS password should now be removed, providing access to the BIOS settings.

Note: These are the most reliable methods to reset the BIOS settings on your PC to remove the BIOS password. Alternatively, third-party utilities can also serve to reset the BIOS password, but they may not work for all manufacturers and can be considered outdated.

Should you encounter issues resetting the BIOS password with these methods, you should contact the support team for your motherboard manufacturer for further assistance.

The post How to Remove Your Computer’s BIOS Password When Forgot? appeared first on Appuals.

In addition, visual artifacts may be caused by the video cable connecting your monitor to your GPU. This article presents multiple methods you can use to resolve the artifacting issue on your system.

1. Use a Different Video Cable

If you encounter artifacts, try using an alternate video input cable with your system. A defective cable can disrupt communication between the GPU and your monitor, leading to artifacts.

Therefore, switch out your video input cable to see if the problem persists. You can also try different ports on both your GPU and monitor to determine if that resolves the issue.

2. Turn off G-Sync (if applicable)

G-Sync is a feature in some monitors designed to eliminate screen tearing. However, if you are using a monitor with G-Sync support and encounter artifacts, the feature may be malfunctioning.

First, access the monitor’s settings menu to find and disable the G-Sync function. Alternatively, use the NVIDIA Control Panel to turn it off.

1. Open the NVIDIA Control Panel on your system.
2. Navigate to the Set up G-SYNC option on the left.

   

3. Deselect the Enable G-SYNC checkbox and click Apply.

   

4. Determine if this step resolves the issue.

3. Reinstall Graphics Drivers

Corrupted or outdated graphics drivers can also cause artifacts on your monitor by preventing proper communication with the GPU. To resolve this, a clean installation of the graphics drivers is necessary.

1. Download the Display Driver Uninstaller (DDU) utility from the official website here.
2. Extract the downloaded file to a location on your drive.
3. Open the Display Driver Uninstaller.exe file from the extracted folder.
4. In DDU, press the Continue button in the Options dialog box.

   

5. Use the Select Device type menu to pick GPU.

   

6. Choose your GPU manufacturer from the Select device menu.

   

7. Select the Clean and restart option to remove your video drivers.

   

8. Once your PC reboots, visit your GPU manufacturer’s website and download the latest drivers for your graphics card.
9. Install the newly downloaded drivers and check if the artifacts still occur.
10. If the issue began after a recent driver update, reverting to an older driver version may solve the problem.

4. Reseat Graphics Card

If your GPU is not correctly inserted into the motherboard, this could lead to screen artifacts. This is especially common after moving your computer or if the GPU was never fully inserted initially. To fix this, you’ll need to reseat the graphics card to ensure it’s properly seated.

1. Unplug your computer and open the PC case.
2. Use a screwdriver to remove your GPU.

   

3. Detach the cables connected to the GPU.
4. Find and unlock the GPU by pulling the lever on the expansion slot, which is located beneath the GPU.

   

5. Carefully remove the GPU from the motherboard.
6. Clean the expansion slot to ensure there’s no dust present.
7. Reinsert the graphics card, reconnect the cables, and secure the GPU with screws.
8. Check to see if the artifacts continue to appear.

5. Disable MPO

Multiplane Overlay (MPO) is designed to reduce the workload on your CPU and GPU. However, after a recent NVIDIA update, it has been causing artifacts.

1. Download the NVIDIA-provided registry file for disabling MPO from here.
2. Execute the registry file to implement the necessary changes. This action will disable MPO on your system.
3. Test to see if the problem has been solved.
4. If the artifacts persist, you can re-enable MPO by running the mpo_restore registry file from the same source here.

6. Clean your Graphics Card

Overheating due to dust buildup in your graphics card’s fans can also lead to artifacts. Cleaning the graphics card is necessary in this case.

Use gentle bursts from an air blower to remove accumulated dust from the GPU fans. After cleaning the fans, make sure the rest of the graphics card is dust-free.

Then, reinsert the graphics card into your system and verify if the issue persists.

7. Check your GPU

In cases where the graphics card itself is defective, artifacts on the monitor are a common symptom. A damaged GPU might be unable to render graphics properly due to an internal issue.

To confirm this, test the GPU by installing it in a different computer system. If artifacts show up, unfortunately, your GPU may be faulty. Conversely, if there are no artifacts, another issue may be causing the problem, and you can continue with the next method.

8. Reinstall Windows

If none of the above methods has worked, a fresh installation of Windows may be the solution. This will help to eliminate any software-related problems causing the artifacts.

Before reinstalling Windows, it is highly recommended to format your hard drive and start with a clean slate. Consequently, make sure to back up important data to avoid loss; you can use this guide to back up your data.

Refer to this guide for detailed instructions on performing a clean installation of Windows.

This should address the issue with artifacts in Windows. If the problem continues post-installation, consider contacting the official Microsoft support team or seek assistance from a local PC repair professional.

The post How to Fix Screen Artifacts Display Problem in Windows? appeared first on Appuals.

Basic Troubleshooting

1. Perform a cold restart of the system and monitor.
2. Update the system’s OS and drivers.
3. Try using an alternative display cable or port.

Distinguish if the Issue Is with the Monitor or System

Begin by booting the system into BIOS to check if the lines appear. If present, the monitor likely has an issue, and you should proceed with monitor-specific solutions.

If the black lines are not visible in BIOS, the problem may be with the system; you would then follow system-specific solutions.

Another way to diagnose the problem is to connect the monitor to a different system. Additionally, you could boot the system using a bootable USB drive with another OS to check if the lines disappear.

Monitor-Specific Solutions

1. Use the Monitor’s Auto-Adjust Feature

A mismatch between the incoming video signal and the monitor’s native display output can cause black lines to appear. Using the monitor’s auto-adjust feature may rectify the issue.

1. Access the monitor’s menu and select the Auto Adjust feature. Depending on the model, you might need to use the physical buttons or the touch functionality of the monitor to do this.

   

2. Activate the feature and check if the problem resolves. For certain monitors, it may be necessary to hold the auto-adjust button down to initiate the adjustment process.

2. Check the Monitor’s Temperature

Electronic devices, including monitors, can malfunction at extreme temperatures. If your monitor is too hot or too cold, it might display black lines on the screen. Adjusting the monitor to a more appropriate temperature can solve this issue.

1. If the environment is hot or humid, relocate the monitor to a cool area, preferably air-conditioned. Give the monitor time to adjust to the ambient temperature.

   

2. If the monitor is too cold, move it to a warm place and observe if the issue resolves. An air dryer may be used to assist in warming up the monitor.

3. Connect the Monitor to Another Power Source

Fluctuations in the electricity being supplied to the monitor can trigger anomalies like black lines on the display. Switching to a different power source may fix this issue.

1. Power off the system and monitor.
2. Unplug the monitor from its current power source and connect it to a different outlet.

   

3. Avoid using extension cables or surge protectors initially to see if the problem is resolved.
4. If the issue persists, try connecting the monitor with a surge protector to see if that eliminates the black lines.

4. Check for Electromagnetic Interference Around the Monitor

Electromagnetic interference from nearby devices such as cell phones, Wi-Fi routers, or other electronic appliances can create black lines on a monitor. Eliminating these sources of interference may clear the problem.

1. Power off the monitor and detach its power cord.
2. Turn off mobile phones and routers.

   

3. Activate Airplane Mode on your computer or laptop.
4. Shut down all other electrical or electronic devices in the vicinity, or relocate them to another space.
5. Hold down the monitor’s power button for a minute, replug the power cable, and switch the monitor back on. Check to see if the screen is now free of black lines.

5. Reset the Monitor

Black lines may appear on a monitor if its firmware becomes corrupted. Resetting the monitor to its default factory settings often addresses this problem.

Note: The steps to factory reset a monitor can vary by model and manufacturer. Consult the user manual or the support website for the specific monitor for accurate instructions.

1. Navigate to your monitor’s menu and select the Factory Reset function.

   

2. Choose this option and confirm your selection to initiate the reset process.
3. After resetting, restart the monitor and verify if the black lines have been eliminated.

6. Check for a Loose Connection on the Monitor’s Motherboard

Loose connections on a monitor’s motherboard can cause black lines to appear on the display, often occurring after the monitor has been moved. Inspecting and securing any loose connections may resolve the issue.

1. Power off the monitor and unplug all cables from it.
2. Press the power button for a minute, ensuring that you follow proper ESD protection protocols.
3. Place the monitor on a flat, soft surface to prevent scratching the screen.
4. Remove the screws from the back of the monitor and carefully take off the back cover.

   

5. Clean the internal components and the board if necessary.
6. Reseat all cables and look for any evident physical damage, such as a blown capacitor.
7. Reassemble the monitor, replacing the back cover and securely fastening the screws.
8. Reconnect the monitor to the system, power it on, and check if the black lines have disappeared.

System-Specific Solutions

1. Change the System’s Refresh Rate

If black lines appear because the monitor does not support the system’s current refresh rate, adjusting the refresh rate may solve the problem.

1. Right-click on the desktop and navigate to Settings > System > Display > Advanced Display settings.
2. Set the Refresh Rate to the lowest possible value to see if the lines disappear. You can test different refresh rates to determine which one resolves the issue.

   

2. Disable HDR in the System Settings (if applicable)

Problems with High Dynamic Range (HDR) processing or incompatibility with the monitor’s capabilities can cause black lines. Deactivating HDR in the system settings may correct this issue.

1. Navigate to Settings > System > Display > HDR.
2. Turn off Use HDR and check if the black lines no longer appear.

   

3. Disable V-sync in the System Settings (if applicable)

When a monitor is not correctly synchronizing with the system’s variable frame rate output, it may display black lines. This can be due to V-Sync or similar technologies that alter the frame or refresh rate. Turning off these features could remove the lines.

1. Launch the Nvidia Control Panel and select Manage 3D Settings.
2. Toggle the Vertical Sync setting to off and apply the changes.

   

3. Restart your system and check if the black lines have been removed from the display.

4. Check for a Conflicting App on the System

Occasionally, certain applications may conflict with a system’s display modules, causing black lines on the monitor. Identifying and disabling or removing the conflicting app may resolve the issue.

1. Start your PC in safe mode and determine whether the lines are still present.
2. If not, clean boot your PC and verify if the issue is rectified.

   

3. If the lines are gone, re-enable the services and processes one at a time to isolate which one is causing the issue.

After identifying the problematic app, uninstall it or prevent it from starting with the system. For example, if the Snip app or Snipping Tool on Windows is responsible, removing it should fix the issue.

1. Right-click on the Start button and navigate to Apps & Features.
2. Find the Snipping Tool and click on its options.

   

3. Select Uninstall, confirm the action, and follow the prompts to remove the app.
4. Restart your system and check if the display is functioning normally.

5. Reinstall the System’s Graphics Driver

A compromised graphics driver installation can lead to issues like black lines on a monitor. Reinstalling the graphics driver may resolve this.

1. Download the most recent graphics driver from the hardware manufacturer’s website.
2. Right-click on the Start button and select Device Manager.
3. Expand Display Adapters, right-click on your graphics device, and select Uninstall Device.

   

4. Tick the box for Delete the driver software for this device if available, and then click Uninstall.
5. Once the uninstallation is complete, restart the system.
6. Install the previously downloaded graphics driver and restart the system again to confirm if the issue has been resolved.
7. Should the problem persist, use a software like Display Driver Uninstaller (DDU) to remove the driver completely, and then install the most recent driver. Check if the black lines are no longer appearing.

Further Troubleshooting

If none of the aforementioned solutions resolve the issue and it appears to be related to the monitor, reach out to the monitor’s manufacturer for hardware-specific troubleshooting advice.

If the problem is specific to the system, consider performing a factory reset or reinstalling the operating system.

The post How to Troubleshoot and Fix Black Lines on Your Monitor? appeared first on Appuals.

Troubleshooting Prerequisites

1. Ensure the camera is not zoomed in as this can amplify camera movement and lead to perceived flickering.
2. Modifying lighting conditions may help identify flickering issues, as certain types of lights, like LEDs, operate at frequencies that can interfere with the camera sensor. Experiment by moving to a different room or going outdoors.
3. A brief flicker may occur upon launching the Camera app as it auto-adjusts to lighting conditions; however, persistent flickering is not normal and may indicate an issue.
4. It’s typical for the camera to flicker when pointing at an electronic screen due to the refresh rate of the screen, which, again, should not be persistent.

Basic Troubleshooting

1. Remove any case, film, or accessory that could interfere with the camera’s functionality.
2. Relaunch any apps where the camera flickers, such as Instagram.
3. Try accessing the Camera app through the Lock Screen or Control Center to see if the flickering persists and use this as a temporary workaround if successful.
4. Perform a Restart and Force Restart of the iPhone.
5. Make sure to update both the Camera app and the iOS software on your iPhone.

1. Clear the iPhone’s RAM

Excessive background processes can slow down your device and may affect camera operation. Although clearing RAM is not a standard resolution for camera issues, some users may find it helpful.

1. Navigate to Settings > Accessibility > Touch > Assistive Touch and enable it.

   

2. Go to Settings > General > Shut Down.
3. On the power off slider screen, tap on the Assistive Touch icon and press the Home button. This process is rumored to clear the RAM.
4. After restarting the iPhone, open the Camera app to test if the issue persists.

2. Disconnect the AirPods or Disable Bluetooth

There are anecdotal reports that suggest Bluetooth connections might impact camera performance, although this is not a documented issue.

1. Go to Settings > Bluetooth.
2. Tap on the Info icon next to your AirPods and select Forget This Device.

   

3. Restart your iPhone and observe if the camera performance improves.
4. If necessary, disable Bluetooth from Settings > Bluetooth and restart the device again.

   

3. Disable Night Mode or Deep Fusion on the iPhone

Movement during long exposure in Night Mode or processing in Deep Fusion can cause flickering. Disabling these features may improve stability.

Disable Night Mode

1. Access Settings > Camera > Preserve Settings.
2. Turn off Night Mode, restart your device, and check if the issue is resolved.

   

Disable Deep Fusion

1. Navigate to Settings > Camera.
2. Deactivate Photos Capture Outside the Frame and restart the iPhone to see if the flickering stops.

   

4. Disable Macro Mode in the iPhone’s Camera Settings

Transitioning between camera lenses in Macro Mode can lead to flickering. Disabling this feature might help mitigate the issue.

1. Within Settings > Camera, locate and turn off Macro Control, then restart your iPhone.

   

2. Reopen the Camera app to see if the flickering persists. If necessary, toggle Macro Control back on and assess its effect.

5. Adjust the Camera Exposure

Incorrect camera exposure can cause flickering as the camera tries to adapt to the light. Adjusting the exposure might help.

1. In the Camera app, select the Photo mode.
2. Adjust the Exposure setting to a lower level such as -0.7 and observe any changes.

   

6. Match Video FPS to Light Frequency

Misalignment between the camera’s FPS and artificial lighting frequency could cause flickering. Adjusting the FPS could resolve this.

1. Visit Settings > Camera > Record Video.
2. Choose a frame rate, such as 4K at 30 FPS, honoring the power supply standard of your location, be it 50Hz or 60Hz, and restart the iPhone.

   

7. Lock Camera Settings

Disabling automatic camera switching in variable lighting might prevent flickering but consider how this affects auto-exposure and white balance.

1. Go to Settings > Camera > Record Video.
2. Activate Lock Camera, and restart your device.

   

3. Open the Camera app again to test the adjustment. If issues persist, revert to default settings and consider altering PAL/NTSC settings.

8. Reset All iPhone Settings

If an incorrect setting is causing camera flickering, a reset to default settings may be necessary. Always back up important configurations before proceeding.

1. Go to Settings > General > Reset > Reset All Settings.

   

2. After resetting, check if the flickering is resolved.

Further Troubleshooting

1. Consider a factory reset if problems persist.
2. Contact Apple Support for further assistance–if under warranty, inquire about a replacement. In the meantime, third-party camera apps may serve as alternatives.

The post How to Fix an iPhone Camera Blinking/Flickering Issue appeared first on Appuals.

You might also encounter a black screen, be routed back to the home screen, or receive a notification indicating that Live TV is blocked. It’s worth noting that there have been instances reported where Live TV suddenly stops working at specific times, such as precisely at 11:00.

Basic Troubleshooting 

1. Ensure that Hulu services, especially the Live TV feature, are operational.
2. If the Live TV option does not appear on your Hulu app, verify that the device supports Live TV.
3. Relaunch the Hulu app.
4. Perform a cold restart on your TV, streaming device, and router.
5. Update the Hulu app along with the firmware of your TV or streaming device.

1. Re-log into the Hulu App

Issues with account authorization between the Hulu app and its servers can prevent Live TV from functioning correctly. Re-logging into the Hulu app can rectify this problem.

1. Open Hulu and tap on your profile icon.
2. Select Log out and confirm your choice.

   

3. Restart both your device and router.
4. Reopen Hulu, log in, and check if the Live TV issue has been resolved.

2. Try Another Network

If your Internet Service Provider (ISP) is incompatible with Hulu’s Live TV, this could cause problems. To test if this is the case, connect your device or TV to a different network.

1. Disconnect your device or TV from the current network.
2. Restart the device or TV and connect to a different network. Avoid using a phone’s hotspot unless necessary, as this can lead to connectivity issues with Hulu on TVs or streaming devices.

   

3. Open Hulu again to see if the issue has been fixed.

3. Disable IPv6 on the Router and Device

If your router or device relies on IPv6 for Hulu server communication, but your ISP does not support IPv6 properly, this could disrupt Live TV service. Disabling IPv6 on both your router and device may solve the problem.

1. Access your router’s admin portal via an app or web browser, then navigate to Advanced > IPv6.
2. Disable IPv6, and restart your router, device, or TV. If IPv6 is already disabled, try enabling it instead.

   

3. Relaunch Hulu to determine if the issue has been resolved.
4. If the problem persists, consider disabling IPv6 on the device to see if that addresses the problem.

4. Reinstall the Hulu App

Damaged modules within the Hulu app, particularly following an update, can interfere with the Live TV function. Reinstalling the app can often resolve these issues.

For Android devices, follow these steps:

1. Open device Settings, navigate to Applications > Hulu.
2. Force stop the app, and clear its cache and storage to remove obsolete data.
3. Tap Uninstall and confirm the removal of Hulu.

   

4. Restart the device, reinstall the Hulu app, and log in with your credentials. Verify that Live TV is now working.

5. Set or Change Your Location in the Hulu Settings

Hulu requires location authorization for Live TV, and failure to properly authenticate your location can prevent access. Adjust your location settings within Hulu to resolve this issue.

1. Open a web browser and head to the Hulu website.
2. Log in and navigate to Privacy and Settings.
3. Select Set or Change Home and input a new location.

   

4. On the device with issues, launch the Hulu app and log out.
5. Restart the device, relaunch Hulu, and check if the issue is fixed.

6. Remove Your Device from the Hulu Account Profile

A lack of proper communication between your device and Hulu’s servers can lead to Live TV issues. Removing and then reauthorizing your device might solve the problem.

1. Open a web browser and visit the Hulu account page.
2. Select Manage Devices and remove the problematic device.

   

3. Launch the Hulu app on the affected device and log out. For iOS devices, also remove Hulu from TV Providers in Settings.
4. Restart the device and router, then relaunch Hulu and log in. Verify if Live TV is now operational.

7. Reset the TV or Streaming Device to Factory Defaults

Any damage to essential firmware modules within the TV or streaming device might hinder the execution of Hulu’s Live TV feature. Resetting the device to factory defaults could provide a solution.

Before resetting, remember to backup any important data. To reset a Roku device:

1. Navigate to the Roku device’s Settings, then System > Advanced System Settings > Factory Reset.
2. Choose Factory Reset Everything and allow the process to complete.

   

3. Afterwards, set up your Roku device, reinstall Hulu, and sign in. The Live TV feature should be functioning properly at this point.

Should the issue continue to persist, it’s recommended to contact Hulu Support for additional assistance. They may suggest updating or resetting your IP address to rectify the problem.

The post How to Troubleshoot Hulu Live TV When It’s Not Working appeared first on Appuals.

Basic Troubleshooting

1. Connect the iPhone using a USB cable, preferably without a case.
2. Disable any active VPN connections on the iPhone.
3. Restart the phone, the infotainment system, and the car. For some models, you may need to disconnect the car battery.
4. Ensure that CarPlay is used within a supported country.
5. Attempt connection with an alternative USB cable or adapter that supports data transfer.
6. Update the software on both the iPhone and infotainment system.

1. Remove Wireless Dongle from the Infotainment System

Interference from a wireless dongle can impede CarPlay functionality. Removing the dongle could resolve the issue.

1. Unplug the wireless dongle (e.g., CarlinKit) from the unit, then disconnect the phone.

   

2. Restart both the phone and car.
3. Once the unit powers on properly, reconnect the phone to check if CarPlay functions correctly.

2. Clean the Charging Port of the iPhone

Accumulated lint or dust in the charging port may interfere with the cable’s data connections, resulting in only charging but no CarPlay activation. Clean the port gently to resolve this.

1. Disconnect the phone from the infotainment unit and power off the car.
2. Using a toothpick or compressed air, carefully clean out the iPhone’s charging port.

   

3. After cleaning, restart the iPhone and power on the car.
4. Reconnect the iPhone and test if CarPlay is now working properly.

3. Enable Siri in the iPhone’s Settings

Siri must be enabled for CarPlay to function; if it’s disabled or not allowed on the lock screen, CarPlay may not work.

1. Open the iPhone Settings, then navigate to Siri & Search.
2. Turn on the toggle for Listen for “Hey Siri”.
3. Ensure Allow Siri When Locked is enabled to resolve the issue.

   

4. Enable USB Accessories in the iPhone Settings

If USB Accessories are disabled when the phone is locked, CarPlay may cease to operate. Enable this feature to fix the issue.

1. Open Settings on the iPhone and select Touch/Face ID & Passcode.
2. After entering your passcode, turn on USB Accessories under Allow Access When Locked.

   

3. Restart both the iPhone and car, then check if the issue persists.

5. Remove Restrictions on CarPlay

CarPlay won’t function if it is restricted in the iPhone’s Screen Time settings.

1. Go to the iPhone Settings > Screen Time > Content & Privacy Restrictions > Allowed Apps.
2. Make sure CarPlay is enabled to rectify the issue.

   

6. Disable Bluetooth and Delete Paired Devices

Bluetooth pairing can interfere with CarPlay. Disable Bluetooth and delete paired devices to troubleshoot.

1. Disconnect the phone from the unit and restart both your device and the infotainment system.
2. In the iPhone Settings, navigate to Bluetooth.

   

3. Select Forget This Device for all paired devices and turn off Bluetooth.
4. On the car infotainment system, go to Settings > Smartphone and Bluetooth Device List and delete all paired phones.
5. Restart both your phone and the infotainment system.
6. Reconnect the phone via USB and check if CarPlay is functioning.
7. If not resolved, disable Wi-Fi on both devices and reassess.

7. Reset the Network Settings of the iPhone

Invalid network settings can impair CarPlay. Resetting them might help; back up necessary information first.

1. Unplug the phone from the car and turn off the infotainment system.
2. Head to the iPhone Settings, then General > Reset.
3. Select Reset Network Settings and confirm.

   

4. After the iPhone restarts, power on the car.
5. Reconnect using the USB cable and see if the problem is fixed.

8. Edit the CarPlay Settings on the Phone and Car Unit

Incorrect CarPlay settings can lead to malfunctions. Edit settings on both the phone and infotainment system to address this.

Enable the Phone in the Unit’s Connectivity Settings

1. Access the unit’s Settings and proceed to Connectivity Settings.
2. Enable the phone if it appears disabled, and check for resolution.

Re-enable CarPlay

1. On the iPhone, go to Settings > General > CarPlay.
2. Disable it, then restart the iPhone.

   

3. In the car’s Settings, find and disable CarPlay.
4. After restarting the car, enable CarPlay on both the iPhone and the car.

   

5. Reconnect the iPhone and confirm if the issue has been resolved.

Further Troubleshooting

1. Delete the phone and car from each other’s settings (as described in the disabling steps).
2. Perform a factory reset of the infotainment system.
3. Factory reset the iPhone after backing up essential data.
4. If all else fails, contact car manufacturers or Apple Support for further assistance. Until then, using a wireless dongle may provide a temporary CarPlay solution.

The post How to Fix CarPlay Not Working While iPhone Charges? appeared first on Appuals.

Typically, the battery depletes rapidly within hours or minutes. In severe cases, the battery may fail to charge or even deplete while charging. Additionally, the watch may become excessively hot during charging.

Basic Troubleshooting

1. Restart your Apple Watch, and if required, force restart or restart it while it’s on the charger.
2. Restart or force restart your iPhone.
3. Ensure that both your Apple Watch and iPhone are running the latest available updates.

1. Disable Wi-Fi, GPS, Location, and Bluetooth on the Watch

A bug in watchOS that actively uses Wi-Fi, GPS, location, or Bluetooth could lead to rapid battery depletion.

1. Force restart both the iPhone and Apple Watch.
2. Turn off Wi-Fi on your Apple Watch, force restart it, and check to see if the battery issue resolves.

   

3. If the issue persists, follow the same steps for GPS, location, and Bluetooth, restarting the Watch after each adjustment to determine which setting may be causing the problem. Once identified, leave it disabled until a fix is released.
4. If the problem continues, disconnect (do not unpair) the Watch from the iPhone by turning off Bluetooth on both devices, then reconnect them. Assess whether this resolves the issue.

2. Remove Offline Playlists and Podcasts (if applicable)

The Apple Watch may experience rapid battery drain if Apple Music’s offline playlists are stuck in a continuous synchronization loop after a malfunction.

1. Navigate to an offline playlist in the Music app on your Apple Watch.
2. Press and hold the playlist, select Delete from the menu, and repeat for any remaining offline playlists. Afterward, force restart the Apple Watch and check if the battery problem has been resolved.

   

3. If the problem remains, open the Podcasts app on your Apple Watch, tap on an episode, press and hold until the Options menu appears, and select Remove Download.
4. Repeat the process with all episodes and force restart the Apple Watch. Verify whether the rapid battery drainage has ceased.

3. Disable ‘Unlock with Apple Watch’ Feature on Your Mac

The ‘Unlock with Apple Watch’ feature, when enabled, may cause the watch’s battery to drain quickly due to continuous communication with your Mac.

1. On your Mac, linked to the same Apple ID as your Watch, open System Settings.
2. Navigate to Security & Privacy and disable the Allow Your Apple Watch to Unlock Your Mac option.

   

3. Restart your Mac, iPhone, and Apple Watch, then check if the rapid battery drainage has ceased.

4. Remove Conflicting Applications and Widgets

If an app or widget is conflicting with your Apple Watch following a watchOS update, it may result in accelerated battery drain. Removing such applications and widgets could solve the issue.

Remove the Compass from the Watch Face

1. On your Apple Watch’s Home Screen Watch Face, press the Digital Crown button to remove the Compass complication.

   

2. Restart the Apple Watch and assess whether the battery performance has improved.

Remove the Weather Icon and Widget

1. Access the Today View in the Notification Center on your iPhone and scroll down to Edit, then remove the Weather widget.
2. On the Widget screen, press and hold the Weather widget, then tap on Delete and confirm the removal.

   

3. Restart both your iPhone and Apple Watch, then check if the battery drain issue has been resolved.
4. If the issue persists, go to your weather settings and remove all locations except your home city to see if this resolves the problem.

Check for any Stuck Installation of an App

1. Open the Apple Watch app on your iPhone and navigate to My Watch > General > Software Update to check if an app installation is stuck.
2. If you find a stuck installation, press and hold it, then select Cancel Download and restart both the iPhone and Apple Watch to verify if the issue is solved.

   

Remove Widgets from the Watch’s Widget Tray

1. Swipe up on the watch screen or use the Digital Crown button to open the Widget screen.
2. Press and hold a widget and tap the Minus icon to remove it.

   

3. Remove all widgets from the screen, then restart both your iPhone and Apple Watch to see if the issue has been addressed.

Uninstall Conflicting Third-Party Apps

Apps like Mobyface, Facer, Watchy, and Snoopy Watch Face are known to cause battery drainage on Apple Watch. Security products, particularly those with features like McAfee’s Safe Surf, can also be culprits.

If you have such apps installed, uninstalling them may restore normal battery performance.

1. By pressing the Digital Crown button on your Apple Watch, pull up the Apps screen.
2. Press and hold the display to enter Edit Apps mode, then tap the Delete button for any conflicting app and confirm the deletion.

   

3. After uninstallation, restart the Watch and check if the battery drain issue has ceased.

Reinstall Apple Apps

You may need to delete and reinstall Apple-made apps (Sleep, World Clock, Workout, etc.) on the Apple Watch to address any issues.

1. One by one, uninstall and then reinstall Apple’s built-in apps on your Apple Watch.

   

2. Once all apps have been reinstalled, restart both your Apple Watch and iPhone and determine if the battery drain issue has been resolved.
3. If the problem persists, reinstall all Apple apps on the iPhone and then restart both the iPhone and Watch to see whether this corrects the problem.

5. Re-pair and Reset the Apple Watch

A corrupted OS or essential modules on the Apple Watch due to a recent update could be causing the battery to drain quickly. In such cases, re-pairing and resetting the Apple Watch is often a solution.

Please ensure you have a backup of all necessary data from your Apple Watch and that it is fully charged prior to proceeding.

Re-Pair the Apple Watch

1. Keep your Apple Watch and iPhone nearby each other.
2. Open the Apple Watch app on the iPhone, tap My Watch > All Watches.
3. Next to the problematic watch, tap on the Info icon and select Unpair Apple Watch.

   

4. After the watch is unpaired, restart both your iPhone and Apple Watch.
5. Update your iPhone to the latest iOS version, then pair the Apple Watch as a new device without restoring from a backup. Evaluate whether the issue is resolved.

Reset the Apple Watch Through Its Settings

1. Open the Settings app on your Apple Watch, go to General > Reset, and then select Erase All Content and Settings.

   

2. Confirm the reset and opt to keep the cellular plan if your model supports it.
3. After erasing, pair the watch with another iPhone (not one that previously experienced battery drain). If the problem is resolved, you can then pair the watch with the original iPhone. Should the issue resurface, consider resetting the iPhone to factory settings.

Further Troubleshooting

1. If the battery drain issue continues, verify that the battery health of your Apple Watch is not below 80%.
2. If all else fails, reach out to Apple Support for assistance. Should your watch still be under warranty, consider requesting a replacement.

The post How to Prevent Rapid Battery Drain on the Apple Watch? appeared first on Appuals.